View Full Version : 2.0l Dyno plot sheets - Post yours here!
JScullin
01-26-2006, 07:47 AM
List your mods and post pictures of your sheets so people can see what's possible with what!
cbman
02-06-2006, 10:27 AM
Huh, this thread doesn't look too popular.
I'm going to wait and post my dyno after I get my built engine.
crazyoldcougar
02-06-2006, 11:03 AM
hehe ...i am going to wait until i get one done...
Ness1216
02-10-2006, 11:57 AM
Here are mine. First is stock, Second is with intake cam, cam gear, header, exhaust, and intake.
crazyoldcougar
02-10-2006, 04:07 PM
wow ness is that an accurate weight?
i always thought our cars were considerably heavier..
Ness1216
02-11-2006, 10:26 AM
ehh not really but he didnt have any resistance on the rollers like normal mustang dynoes. IIRC my car weighs 2829 on registration, then i had a wreck so take off a misc 10 lbs lol and then cf hood which is 30 lbs lighter, diff wheels etc. I think the car ended up at 2777.
azervas
03-06-2006, 12:10 PM
Heres mine - Mods are:
PiperX Cone Filter
Replaced 2x Rear back box's with 1 V6 Mongoose back box.
Running 97RON Super Unleaded(premium in the USA?)
http://img.photobucket.com/albums/v181/azervas/Misc/RR-PiperX.jpg
diddy
03-06-2006, 01:41 PM
nice
cbman
03-08-2006, 11:23 AM
Pardon my ignorance what's the mongoose back box?
So, it was probablly done at the wheels, and it looks like your multiplier is about 1.25. You're assuming you're losing 25% at the wheels?
It that accurate?
hmmm...
AngelSpirit
03-08-2006, 03:01 PM
What is this: Running 97RON Super Unleaded(premium in the USA?) :bowdown:
azervas
03-09-2006, 10:43 AM
Its petrol!
Since i had that RR done i'm running 99 RON Super Unleaded petrol now.
Its loads better - the car loves it!!!
As for the mongoose back box - i removed both rear silencers and replaced them with the rear silencer from a mongoose system(british made?)
Turbo Zetec 'tour
10-24-2007, 05:48 PM
Probe pistons
Eagle rods
cometic .065" head gasket
stock head and valvetrain
Custom turbo setup:
T3 60 trim turbo
air/air front mount intercooler
tial 38mm wastegate set to 10PSI
Custom tune by logan motorsports
http://i84.photobucket.com/albums/k17/Dslax/Picture006-2.jpg
cbman
11-18-2008, 01:49 PM
Dyno'ed my car last week. Unfortunately there were some issues with my Greddy Profec EBC. So, the highest boost I ran was only 14psi. I was planning on going to 20psi, and this is with a pretty conservative tune.
http://www.newcougar.org/forums/attachments/2-0l-zetec-performance/35255d1227030578-2-0l-dyno-plot-sheets-post-yours-here-akhp-dyno-11-14-08.jpg
Turbo Zetec 'tour
11-18-2008, 06:58 PM
What size turbo are you running? i wasnt too far behind you with only 10PSI on a T3 60 trim and while i never got it dynoed, im sure i was above that with the Super 60 at 13PSI.
numbers look pretty good though.
cbman
11-25-2008, 03:52 PM
My turbo is a GT2871R with the T3 exhaust housing option. Its capable of 400HP. I kind of wish I would have gone a little smaller so my spool-up was faster. Although, it looks like my torque peaks sooner that yours.
Turbo Zetec 'tour
11-25-2008, 05:21 PM
i noticed that, its only a couple hundred RPMs so i suspect thats because of the BB turbo since the T3 Super60 and GT2871R are very similar performers with the GT2871R being able to flow just a little more CFM.