2.5l Dyno plot sheets - Post yours here!

[JScullin]

List your mods and post pictures of your sheets so people can see what's possible with what!

Edit by DanG: The discussions should go to PMs or separate threads. This thread should be dyno plots only, to keep it readable. I'm pulling all the extra posts out.

[gyger]

http://www.domesticcompact.com/club/dyno.jpeg
Here's mine
I hit a 172FWHP N/A
SVT UIM,LIM,TB, 19lb injectors
Titan CAI
Underiven crank pulley
MSDS headers and y-pipe ceramic coating
Tru-bendz test pipe
flowmaster-< tru-bendz exhaust
S-AFCII
VCN-1000 running a 50 shot

basic bolt-ons

[frenchblueC2]

lame ATX, but here it is anyway. I doubt my changes from stock made much of a difference, but I'm listing everything anyway.

KKM air intake
Borla dual catback exhaust
DMD
Mobil 1 5w30
Mobil 1 ATF
93 octane

http://www.newcougar.org/forums/attachment.php?attachmentid=22730&stc=1&d=1139164215

[Shagmonkey]

http://www.cougardb.com/image.php?id=6810&raw=1

Fully gas flowed, ported and blue printed
Uprated oil pump
Uprated water pump
Uprated fule pump
Weapon-R Headers
Custom duel exit Blue Flame exhaust system
All the CATS were removed
Fast Road CAMs

Standard ECU, injectors and air intake (as all these were being ripped out when the Pro charger went on 1 week after this graph was done)

Paul

[GrandMasterKhan]

I have long since lost my dyno Sheet. When I dynoed my cougar back in 03 i Put down the following

155whp.
150wtq

Mods at that time:

Polished GMK CAI
MSDS headers & ypipe
Gutted and modified OEM cat with 2.25" exit
Flowmaster dual exhaust (truebendz) 2.25 inlet/2.5" outlet
Denso Iridium plugs
SVT UIM & LIM & TB
stock injectors and tuning.


I plan on dynoing again very soon with my newer 2.5L setup.

[nandalora]

This is from over a year ago.......BEFORE the 3.0L :tongue:

Mods:
SVT UIM, LIM, T/B
Gutted precats, testpipe, True Borla split rear exhaust
GMK carbonfiber CAI :cool:, Ford Racing plugwires, NGK splitfire plugs

The pull in RED is 87 octane, the pull in BLUE is 93! Been using 93 eversince:biggrin: If you can't read, it says 163.3 HP & 159.3 TQ

[skater]

Here is mine. I think there was something funny going on with my engine when it was done; in particular I wonder if the alternator started causing problems at the top end (though it certainly doesn't look it).

This is a completely stock MTX V6 Cougar except for a K&N Drop-in Filter and Ford Racing 9mm plug wires. The plugs and wires were new as of a few months before this dyno was done. The UIM and LIM had never been cleaned and the car had over 60,000 miles on it.

(Not a real good graph, I know. I'm working on producing a better one.)

22890

[Rikenbomb]

Confirmed by DanG my 2.5L was a factory freak. Dyno'd at CF 2003 I pulled DynoJet IIRC.

153 whp
147 wtorque

Mods at that time included:
KKM filter with BAT gooseneck
SVT UIM and TB
Bosch Platinum +4 plugs (In good condition when removed :crazy: )
Trubendz Flowmatster AS dual exhaust

Dyno will be posted when I can get it scanned.

[99ADCCOUGAR]

This car USED to belong to my brother--he says he had some high compression pistons put in.

What I have put in

SVT:
*UIM
*LIM
*CAMS
*GEARS
Unorthodox Racing:
*Pulleys
ADC:
*2.5 NA Chip
Zex
*50 shot


http://i48.photobucket.com/albums/f245/BBoyFunky/dynosheet.jpg

id say that im doin allright...
199 fwhp
190 fwtq

[AndyMan]

here's what i got...
GMK CF CAI, SVT TB, SVT UIM,
Unordx pulley, Viteck racing wires,
Weapon R headers, Yipipe, custom 2.25 full catback exhaust
Stage 1 spec clutch & Lightweight Fidanza Flywheel...
... just call me bolt-on-wonderboy.. lol
i don't have any tunning at all

here's my numbers...
HP between 152.1 & 154.4
TQ between 143.5 & 146.8
.. and some other weird graph...

HPhttp://i81.photobucket.com/albums/j233/Andyman4/DSCN0508.jpg

TQ
http://i81.photobucket.com/albums/j233/Andyman4/DSCN0507.jpg

... other
http://i81.photobucket.com/albums/j233/Andyman4/DSCN0509.jpg

[tino]

Not a cougar but my 1998 SVT Contour. KKM, Gutted precats, Magnaflow exhaust, modded stock y-pipe. Hehe and 220K on the odometer when the runs were made :) I'm now at over 250K and still going strong (knock on wood)

http://powerthings.com/pics/latestruns.jpg

[tony]

this was my furst set up run after building the car ,,, but only had 3/4 throttle so still more to come lol

[pwhitelock]

Blueflame exhaust and induction kit:

173BHP
Cant remember torque.

Aint got graph either :rolleyes:
Now fitted performance ignition leads, and got MSDS headers on there way soon.:biggrin:

[Newcat016]

As for mine, i was hoping for alittle more hp but after the tune it came to
150hp at 6200rpm and 140tq at 4300rpms. As for mods to the engine I have svt uim,lim,tb,cams,injectors,cai,msds headers, y-pipe, flowmaster exhaust,xcal2 tune to 93 octane and thats it.o yeah, its an auto.

[Dom1013]

Dyno'd 01 ATX Sport Pkg. Coug on a DynoJet today

-K&N Intake Kit
-Replaced muffler w/aftermarket "rice" one

131.91 hp
135.59 tq

dont really know if there's a need to even put the dyno graph up...just needed a baseline run before anything big goes on...

[work_in_progress]

Just got mine dyno'd today on a Mustang Dyno:

167.0HP @ 5957...189.0 WCF
171.3TQ @ 4418...193.9 WCF

2.5' cat-back, Weapon-R air filter

Kinda thinking I'd push a little more, seeing those WCF's give me hope tho.

[daniel]

well after 5 months of work on my prototype turbo kit and a big thanks to joey on

11psi on a all stock 2.5 no svt parts

278whp:biggrin:

did get an hp on 13psi.

[23racer]

I don't have adyno sheet like yours, I just have the one that came with my car.

It's a naturally aspirated 2.5l, runs with a Ford ecu and the emissions have been taken off. I think its okay and it goes quick enough, but it is a bit loud, :evil:.

Eric

[skater]

I don't have adyno sheet like yours, I just have the one that came with my car.

It's a naturally aspirated 2.5l, runs with a Ford ecu and the emissions have been taken off. I think its okay and it goes quick enough, but it is a bit loud, :evil:.

Eric

A 2.5L that dynos at 268 HP? :confused:

[southsiderida90]

yea, that didnt sound right when i read it either, it sounds like its not whp, but at the crank,if not, please tell what you have modified to get to that point.

[boarder4life]

its a fully built race motor. apparently after it was done and installed it was actually putting out more.

in the ontario section he has posted picsand info on everything from the car.its a work of art all the custom machining put into the suspension and tranny.

[skater]

I don't have adyno sheet like yours, I just have the one that came with my car.

It's a naturally aspirated 2.5l, runs with a Ford ecu and the emissions have been taken off. I think its okay and it goes quick enough, but it is a bit loud, :evil:.

Eric

its a fully built race motor. apparently after it was done and installed it was actually putting out more.

in the ontario section he has posted picsand info on everything from the car.its a work of art all the custom machining put into the suspension and tranny.

That would make a lot more sense. His description made it sound like it was a stock 2.5L with just the cats removed.